Associated model number: 3060 Mini-Transmitter

Congratulations! You have just purchases a Mini-Code Digital Transmitter, which we believe to be the finest product of its kind on the market. With a little care this transmitter should provide you with many years of excellent service. Please take a moment to read the following instructions and you will find that setting your new transmitter will be quite an easy matter.


The model 3060 Mini-transmitter case is composed of 2 halves which are held together by a small Phillips head screw. Removing this screw will allow access to both the code setting switch and the battery compartment.


Set both transmitter and receiver switches to the code of your choice, being sure both are set the same since a different setting of just one switch will prevent operation. The digital code is determined by the position of 10 small switches numbered 1 through 10 located in the receiver and transmitter. Any combination of “on” or “off” positions can be selected by using a pencil or ball point pen. (NOTE: The switches are in the “on” position when the switch is depressed toward the number.)

Once code have been set, check operation and reassemble the transmitter case.


This transmitter is completely self contained, including battery and can be operated while held in hand or while mounted in the car. It is supplied with “hook and loop” fabric for easy mounting or it may be added to your key chain using the slot provided.

Transmitter battery replacement

Replacement battery – 12volt alkaline lighter battery (Eveready A 23 or equivalent)

The transmitter battery can be checked or changed by removing the Phillips head screw located on the back of the case and carefully separating the case halves to expose the circuit board and battery. Simply slide out the old battery and slide in the new, remembering to observe the battery compartment. Note that if the red L.E.D. on your transmitter fails to light you most likely have a weak or dead battery and it should be replaced.


To check operation, move back a reasonable distance (about 50 ft) and press the transmitter button. Operation should be reliable at this distance but environment and location of both the transmitter and receiver will affect the range. If the transmitter is stowed well out of sight, it may be necessary to remove it from its mounting and hold near the windshield. Try different locations and positions. If operation is still unsatisfactory, the problem may be isolated by:

  1. Checking the door operator. If the door will not open when the wall button is pressed, the problem is likely to be the operator. If the door will open by pressing the wall button, but not when the radio control button is pressed, the problem is probably in the radios.
  2. Replacing the transmitter battery. If after performing the above operational checks, the controls still do not function, they should be returned to your dealer for repair or replacement.

CAUTION: Any changes or modifications in intentional or unintentional radiators which are not expressly approved by LINEAR CORPORATION could void the user’s authority to operate the equipment. This applies to intentional and unintentional radiators certified per part 15 of the F.C.C. rules and regulations.

This device complies with the FCC Part 15 and industry Canada Rules and Regulations. Operation is subject to the following two conditions: (1) This device may cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.


Contact Us

We invite your inquiries regarding your garage door opener.

  • For technical and compatibility issues, we must know the brand and model of your opener to help
  • Be sure to include your complete and accurate email address with your inquiry
Name A value is required.
Email Address (accurate) A value is required.Invalid format.
Phone No.
Brand of Opener
Model Number of Opener
(located on motor head behind light bulb cover)
Model Number of Remote Control
(located on back of remote)
Model/Part Number of Current Receiver
(located on Receiver)
Enter Security Code

Comments: - Owned by 1st Garage Door Openers, Inc., an independent family owned and operated business serving the Garage Door and Garage Door Opener Industry since 1981. Providing excellent customer service and assistance for over 25 years. We are a discount reseller of garage door opener remotes, repair parts, keyless entry and gate operator controls for your home, business, or gated community. We carry parts for the following garage door openers: Lift-Master, Chamberlain, Sears Craftsman, Access Master, Sears Best Craftsman, Sears Automatic Door Opener, Master Mechanic, Security +, Formula 1, Garage Master, Billion Code, LiftMaster Professional, Estate Series, Premium Series, Contractor Series, Power Driver, Whisper Drive, Genie, Alliance, Norelco, Blue-Max, Lift-A-Door, Pro Max, Hercules, Stealth, Excelerator, Intellicode, Genie Pro, OverDrive, Python 2, Signature, Phantom, Legacy, Medallion, CodeDodger, Overhead Door, Genie Shop Vac, Stanley, Vemco, Quiet Glide, SecureCode, Lightmaker, Innovative Products, Whistler, U-Install, Popular Mechanics, Allister, Allstar, Pulsar, MVP, Challenger, GTO, All-O-Matic, Electrolift, Westinghouse, AM/11, Linear, Access Pro, Moore-O-Matic, MegaCode, Delta 3, MultiCode, Heddolf, ESP Micom, Intercontinental Dynamics, Crusader, Wayne Dalton, iDrive, Door Master, Quantum, Classic Drive, Tec Key, Martec, Monarch, Telectron and other garage door openers, and gate operators. Brand names of Garage Door openers are registered trade names of the respective entities and are only used for reference.